VR05S12 XP Power

DC-DC Converter VR05 Series 0.5 Amp Non Isolated 0.5A Switching Regulator xxx Series Regulated Single Outputs from 3.3 to 15VDC Wide Input Range to 36V SIP3 Package High Efficiency to 95% Class B Conducted & Radiated Emissions Short Circuit Protection Low 0.1mA Standby Input Current -40C to +85C Operation MTBF >2MHrs 3 Year Warranty Dimensions: The VR05 provides a cost effective compact efficient switching regulator solution operating from a VR05: 0.457 x 0.401 x 0.297 (11.6 x 10.16 x 7.55mm) wide range DC input. Output voltages start from 3.3V and the VR05 consumes as little as 0.2mA when idle. Models & Ratings (1) (2) Input Current Efficiency Max. Capacitive Input Voltage Output Voltage Output Current Model Number Load No Load Full Load Vin, Min. Vin, Max. 4.75-36V 3.3V 500mA 1.5mA 416mA 680F 89% 80% VR05S3V3 6.5-36V 5.0V 500mA 0.2mA 446mA 680F 90% 84% VR05S05 12-36V 9.0V 500mA 0.2mA 412mA 680F 93% 90% VR05S09 15-36V 12V 500mA 0.2mA 436mA 680F 94% 91% VR05S12 19-36V 15V 500mA 0.2mA 422mA 680F 95% 93% VR05S15 2 3 Notes 1. Full load input current measured at minimum input voltage. 3. Standard tube quantity 43 pcs. 2. Efficiency measured at full load. Mechanical Details FOOTPRINT 0.085 (2.15) 0.02 (0.5) FRONT VIEW (TOP VIEW) Pin Connections 0.039 0.4 ( 1.00) Pin Positive Negative (10.16) 1 2 3 2 3 1 2 3 0.297 1 Vin Vin 0.02 (7.55) 0.012 (0.3) (0.50) 2 Ground -Vout 3 +Vout Ground 0.1 0.457 (11.6) (2.54) 0.2 (5.08) 0.161 (4.10) UNDERSIDE VIEW 0.2 (5.08) Notes 1. All dimensions are in inches (mm) 4. Case & pin tolerance: 0.02 (0.5) 2. Weight: 0.0039lbs (1.8g) approx. 3. Pin diameter: 0.020.004 (0.70.1) www.xppower.com 1 DC-DC Converter VR05 Series Input Characteristic Minimum Typical Maximum Units Notes & Conditions Input Voltage Range 4.75 36 VDC See Models and Ratings table. Input Filter Internal capacitor Input Reflected Ripple 20 mA pk-pk Input Surge 45 VDC For max. 100ms. Output Characteristic Minimum Typical Maximum Units Notes & Conditions Output Voltage 3.3 15 VDC See Models and Ratings table. Initial Set Accuracy 2.0 4.0/3.0 % 3.3V/others (At full load) Minimum Load 0 mA No minimum load required. Line Regulation 0.2 0.4 % Full load over input voltage range. Load Regulation 0.3 0.6 % Maximum variation applies to 3.3V output models. Transient Response 2 % For 50% load change. Recovery in 100s. Ripple & Noise 75 mV pk-pk 20 MHz bandwidth. Short Circuit Protection Continuous, with auto recovery. Maximum Capacitive Load See Models and Ratings table. Temperature Coefficient 0.03 %/ C Overload Protection 1.0 A Start-up Time 20 ms General Characteristic Minimum Typical Maximum Units Notes & Conditions Efficiency 92 % See models and ratings table. Isolation: Input to Output 0 VDC Non isolated. Switching Frequency 550 850 kHz At full load, nominal input. Mean Time Between Failure 2 MHrs MIL-HDBK-217F. Weight 0.0039 (1.8) lb (g) Case Material Non-conductive black plastic UL94V-0. Pin Material Solder coated phosphor bronze C5191R-1/2H. Potting Material Polyurethane type L780 UL94V-0 rated. Water Wash Use de-ionised water only, dry thoroughly. Wave solder peak, 1.5mm from case 10s max. Not suitable Soldering Temperature 260 C for vapour phase soldering. For further details contact XP Power applications team. Environmental Characteristic Minimum Typical Maximum Units Notes & Conditions Operating Temperature -40 +85 C See derating curves. Storage Temperature -55 +125 C Case Temperature +120 C Humidity 95 %RH Non-condensing. Cooling Natural convection. www.xppower.com 2