MAX31343SHLD#

Click here for production status of specific part numbers. Evaluates: MAX31343 MAX31343 Shield General Description Shield Contents The MAX31343 shield is a fully assembled and tested Assembled MAX32625 PICO controller board PCB to evaluate the MAX31343, low-cost, extremely Micro USB cable 2 accurate, real-time clock (RTC) with an I C interface and power management. The shield operates from a Assembled circuit board including MAX31343EKA+T single supply, either from a USB or external power sup- ply, and the integrated microelectromechanical systems Quick Start (MEMS) resonator enhances the long-term accuracy and eliminates the external crystal requirement in the system. Required Equipment 2 This device is accessed through an I C serial interface One pico ammeter for measuring the current provided by a MAX32625 PICO board. One oscilloscope and one oscilloscope probe The MAX31343 shield provides the hardware and soft- ware user interface (GUI) necessary to evaluate the One PC or laptop with Microsoft Windows 7 or later MAX31343. The shield includes a MAX31343EKA+T. It One USB A male to Micro-B male cable connects to the PC through a MAX32625 PICO board and a Micro USB cable. One assembled and programmed MAX32625 PICO board Features One MAX31343 shield Easy Evaluation of the MAX31343 +1.6V to +5.5V Single-Supply Operation Proven PCB Layout Ordering Information appears at end of data sheet. Fully Assembled and Tested Arduino /Mbed Platform Compatible Shield Photo PICO Board Photo Arduino is a registered trademark of Arduino, LLC. Mbed is a registered trademark of Arm Limited. Windows is a registered trademark of Microsoft Corporation. 319-100521 Rev 1 5/20MAX31343 Shield Evaluates: MAX31343 Procedure The shield is fully assembled and tested. Use the follow- ing steps to verify board operation. 1) Place the MAX31343 shield on a nonconductive sur- face to ensure that nothing on the PCB gets shorted to the workspace. 2) Verify that all jumpers are in their default position as shown in Table 1. 3) Connect the MAX32625 PICO board to the shield at the location shown as MAX32625 PICO (Figure 1). 4) Connect the USB Type A male to Micro-B male cable between the MAX32625 PICO board and PC/laptop. 5) Go to the MAX31343 shield product page to download and install the latest version of the MAX31343 RTC SHIELD Software. Figure 1. Connection and Setup 6) Open the MAX31343 RTC SHIELD Software, shown in Figure 2. Table 1. Jumper Settings JUMPER SHUNT POSITION DESCRIPTION 1-2* Connects clock output to pin 6 of P2 Arduino/Mbed connector JU1 Open Disconnects clock output from Arduino/Mbed connector 1-2 Connects backup supply to external DC supply 1-3 Connects backup supply to supercapacitor JU2 1-4* Connects backup supply to ground Open Disconnects backup supply 1-2* Connects interrupt signal to pin 3 of P2 Arduino/Mbed connector JU3 Open Disconnects interrupt signal from Arduino/Mbed connector 1-2 Connects VCC supply to +1.8V on-board supply 1-3* Connects VCC supply to +3.3V on-board supply JU4 1-4 Connects VCC supply to +5.0V on-board supply 1-5 Connects VCC supply to external DC supply Open Disconnects VCC 1-2* Connects VCC to MAX31343 IC WLP package (U1) JU5 Open Disconnects VCC from MAX31343 IC WLP package (U1) 1-2* Connects square-wave output to pin 4 of P2 Arduino/Mbed connector JU8 Open Disconnects square-wave output from Arduino/Mbed connector 1-2* Sets MAX31343 WLP package (U1) IC under test JU10 2-3 Sets MAX31343 TDFN package (U2) IC under test 1-2* Connects VCC to MAX31343 IC TDFN package (U2) JU11 Open Disconnects VCC from MX31343 IC TDFN package (U2) 1-2* Connects VBAT to MAX31343 IC WLP package (U1) JU12 Open Disconnects VBAT from MAX31343 IC WLP package (U1) 1-2* Connects VBAT to MAX31343 IC TDFN package (U2) JU13 Open Disconnects VBAT from MAX31343 IC TDFN package (U2) *Default position Maxim Integrated 2 www.maximintegrated.com